ANAN-10

1950 €

Ses caractéristiques en font un transceiver SDR hors du commun.

Il a actuellement la note maximale sur le site d’évaluation Eham (http://www.eham.net/reviews/detail/10814 ) :

- couverture continue de 10 KHz à 55 MHz

- Puissance de 15 à 20W selon bandes et conditions (10 à 15w sur 6m)

- jusqu’à 1152 kHz de largeur d’affichage de la bande écoutée

- possibilité d’écoute de 7 bandes simultanément (selon PC et logiciel)

- IP3 de 50dB sans préampli et de 30 db avec préampli de 20 dB

- réjection d’image >110 dB à la réception comme à l’émission

- Dynamic range de 125 dB mini

- liaison haut débit avec le Pc par cable ethernet

- etc ...

Specifications & Highlights :

  • Continuous, uninterrupted, receive coverage from 10KHz to 55MHz. .
  • Supports Real-Time display of entire sectrum from 0-55mHz (with suitable PC software)
     
  • Supports 7 fully independent receivers (sharing the same antenna - and with suitable PC software)
     
  • Each receiver can display 48/96/192/384/1152kHz of spectrum
     
  • Blocking Dynamic Range (ARRL Method) no detectable gain compression
    below ADC overload
     
  • Transmit and receiver image rejection > 110dB
     
  • Full duplex operation, any split over entire 160m to 6m range.
     
  • Transmitter two-tone 3rd order IMD of -50dBc on 20m @ 400mW output
     
  • Built-in high performance preamp, with a noise floor typically -135dBm in 500Hz
     
  • Software-selectable 31dB input attenuator in 1dB steps
     
  • High performance receiver – same specifications as the HPSDR Mercury receiver (ie Dynamic Range typically 125dB)
     
  • FPGA code can be updated via the Industry Standard TCP/IP network Ethernet connection
     
  • Seven user-configurable open-collector outputs, independently selectable per band and Tx/Rx (for relay control, etc - with sequencing via PC code)
     
  • Separate open-collector PTT connection for amplifier control, etc, with sequencer
     
  • Microphone PTT jumper-selectable from tip or ring connection
     
  • Bias for electret microphones via jumper
     
  • Four user-configurable 12 bit analogue inputs (for ALC, SWR etc)
     
  • Three user-configurable digital inputs (for linear amplifier over temperature, etc)
     
  • Can operate from a 13.8v DC supply or 12v and 5v supplies
     
  • Jumper selected in-built low noise and high efficiency switch mode power supply designed by Kjell Karson,LA2NI – less than 600mA (receive - one receiver) from a 13.8V supply
     
  • I2C bus connector for control of external equipment
     
  • Full QSK operation (performance dependant on associated PC and control software)
     
  • Low-level transmitter output for transverter use via user-selectable output attenuator
     
  • Stereo audio outputs at line and headphone levels
     
  • In-built 1W stereo audio amplifier for directly driving speakers
     
  • Direct, de-bounced connections for a Morse key (straight or iambic) and PTT
     
  • Low phase noise (-137dBc/Hz @ 1kHz) 122.88MHz master clock, which can be phase-locked to an internal 10MHz TCXO or external fequency reference
     
  • Low phase noise (-140dBc/Hz @ 1kHz at 14MHz) 122.88MHz master clock,
    which can be phase-locked to an internal 10MHz TCXO or external frequency
    reference
     
  • Direct ribbon cable interface to Apollo 15W power amplifier, low pass filters and automatic ATU
     
  • Industry Standard TCP/IP network Ethernet interface supports static, APIPA or DHCP IP address
     
  • Hermes responds to ping and ARP requests and auto senses network connection speed
     
  • Eight (8) Layer PCB design for the most professional, state-of-the-art, design available.

     
  • Custom build rugged Extruded Housing for Hermes and the PA
    (note : no ventilation holes required in .mil style designs)
     
  • Mosfet 10W Linear amplifier (160M-6M) gives 15-20W out on HF and 10-15W on 6M
     
  • LPFs for the PA harmonic suppression and receiver filtering
     
  • Software Configurable Triple antenna ports
     
  • SWR Bridge, enables Forward and Reverse Power plus SWR to be displayed using suitable PC software.
     
  • T/R, LPF Switching using mechanical relays (gold plated contacts)
     
  • Reverse Polarity protection with resettable fuse
     
  • All cables, Hardware and instructions to make a complete transceiver with Hermes
Vue arrière Vue avant

Leaflet ANAN

Notice utilisation anglaise